How-to / SOLIDWORKS

How to put a texture or pattern on a moulded part in SOLIDWORKS without undercuts

A relief built along the surface normal undercuts wherever the face turns away from the mould’s pull, most of all next to the parting line, and SOLIDWORKS’ Draft feature cannot fix a texture of hundreds of faces. Pattern Mapper, Surface Displace and Geometric Surface take the pull directions as reference planes and a draft angle and build the pattern so it leaves the mould: walls drafted along the pull, textures and tiles lowered just as far as needed, the result measured after every build.

Video (1:09, English): Easy to design, hard to mould: 905 vent holes with draft in SOLIDWORKS. Also on YouTube.

Why a texture undercuts

  • A mould half pulls along one direction. Every face of the part has to look along it by the draft angle, or the part scrapes or locks when it comes out.
  • A relief built along the surface normal (as Wrap, Emboss or a displacement does it) leans with the face. Where the face turns away from the pull, near the parting line, its walls face backwards: an undercut. A pattern that was fine in the middle of a mould half locks the part at its edges.
  • The deeper and steeper the relief, the further from the parting line it starts: a knurl or pyramids undercut where the face is still 20 to 30° off the parting line, soft domes only close to it.

What SOLIDWORKS offers built in

  • Draft Analysis (Evaluate tab) colours faces by their draft against a direction: it shows the undercuts, it does not remove them.
  • Draft tilts chosen faces about a neutral plane or a parting line. It works on walls you modelled; on a texture or a relief of hundreds of small faces it is not practical, and on free-form faces it often fails.
  • Wrap embosses, debosses or scribes a closed 2D sketch onto one face. The Analytical method takes planar, cylindrical and conical faces (and extruded or revolved ones); the Spline Surface method takes other faces but distorts the sketch as the curvature grows, and it cannot go all the way round a closed face.
  • 3D Texture turns a texture appearance into geometry, but the result is a mesh (graphics) body for the whole body: no exact B-rep faces, heavy files, and most modelling features no longer apply after it.

Emboss, deboss and studs with drafted walls (Pattern Mapper, Pattern Bodies)

  1. 01Select the faces, then SWPlugins Suite tab › Pattern Mapper, Output Emboss or Deboss (or Body mode for studs and pins).
  2. 02Tick Along a pull direction and pick the mould’s planes in the Pull directions box: Front, Top, Right or your own. Each plane is a direction both ways, the two mould halves. Several planes for slides: each shape takes the one its faces look along.
  3. 03Set the Draft angle: pockets get wider towards their opening, raised shapes and studs narrower towards their top; each keeps its size where it meets the face.
  4. 04A shape that cannot leave the mould is left out and listed with its reason and what would help. Across the parting line = Trim there builds a rib around a bottle in parts, each along its own half.

Textures and tiles (Surface Displace, Geometric Surface)

  1. 01Select the faces, then SWPlugins Suite tab › Surface Displace (an image or a texture preset) or Geometric Surface (tiles, strips, creases).
  2. 02In the Pull direction group tick Along a pull direction, pick the planes and set the Draft angle.
  3. 03Raise along: Surface normal keeps the texture’s look and lowers it where the draft needs it, down to nothing on faces along the pull; Pull direction moves every point along the pull, so it never undercuts, but keeps less depth on steep walls.
  4. 04Not demouldable: Lower to fit (as far as needed), Fade out, or Build anyway to see where it would lock. Geometric Surface lowers each tile as a whole by default, so it keeps its shape and its sharp creases; Lower = Per point keeps relief on both halves of a cell across the parting line.
  5. 05Update preview: the message says the least draft found on the result and red marks show where it falls short.

Good to know

  • Towards a parting line and where two directions meet, the texture fades out over the Edge fade, so the mould halves meet on a clean surface.
  • The check is made on the built faces, not on the settings: what the message reports is what the part has. A part that uses it needs version 1.9 of the add-in.
  • Draft angle 0 means no undercut, nothing more. Textured mould surfaces usually need more draft than polished ones: a common rule of thumb is 1 to 1.5° more for every 0.025 mm (0.001 in) of texture depth; ask your mould maker or texture supplier.

Try it on your own part

Pattern Mapper, Surface Displace, Geometric Surface, Pattern Bodies are part of Advanced Patterns, a module of the SWPlugins Suite, a SOLIDWORKS add-in (2023 or newer). Every tool works free for 14 days; a licence is €149.25 plus VAT for the whole Suite, single modules from €44.25 (launch price until 30 November, regular €199 and from €59), one-time.

Docs: Pattern Mapper · Surface Displace · Geometric Surface · Pattern Bodies

Questions

Related